-
+1 - 312-224-1615
Get in touch with us
-
support@helpwithassignment.com
Send us an e-mail
Solution Library
Write A Report On Renewable Energy House Project
Question Write a report on Renewable Energy House Project which includes the following: 1. Theoretical Approach. 2. Experimental Approach. 3. Data Collection and Data Analysis. (cost , efficiency …..etc. ) Summary The question belongs to Physics and it discusses about writi ... Read More
Reads ( 1225 )| Price:
Original Price: |
Add to Cart |
Calculate Cable Tension Required To Hold A Scoreboard In A Stadium
Question A basketball scoreboard that weighs 9 kN is to be hung from the roof frame of an indoor stadium using a cable ABC. The ends of the cable are attached to hinges at points A and C. Before the scoreboard is attached at B, the midpoint, cable ABC is slightly slack (i.e. it is longer than 3 met ... Read More
Reads ( 2413 )| Price:
Original Price: |
Add to Cart |
Calculate Reaction At Supports For Beam Supporting Uniformly Distributed Weights
Question A beam of length 8m is simply supported at its end as shown in figure.The whole beam carries a Uniformly Distributed Load(UDL) of 10 kN/m together with two point loads of 120 kN and 80 kN. The 120 kN load is at a distance of 2.5m from the left-hand support and the 80kN load is at a distanc ... Read More
Reads ( 2026 )| Price:
Original Price: |
Add to Cart |
Calculate Greatest Point Of Load Applied At Centre Of Steel Cylindrical Tube
Question A steel cylindrical hollow tube, with outside diameter of 16cm and a thickness of 20mm is used as a beam over a span of 6m, being simply supported at its ends. The maximum bending stress of the tube is 125MPa. Neglecting the mass of the mass of the tube, determine the greatest point load t ... Read More
Reads ( 1882 )| Price:
Original Price: |
Add to Cart |
Calculate Least Radius Of Gyration and Slenderness Ratio Of Concrete Column
Question A hollow concrete column has a rectangular cross-section with an external breadth of 300mm and an external depth of 600mm.The internal breadth is 240mm and the internal depth is 520mm.The compressive resistance of the concrete is 200 N/mm2.If the effective height of the concrete column is ... Read More
Reads ( 2291 )| Price:
Original Price: |
Add to Cart |
Calculate Maximum Stress And Angle Of Twist In Degrees For Cylindrical Shaft
Question A 1.5m long cylindrical shaft has an external diameter of 60mm and an internal diameter of 30mm.The shaft is subjected to a torque of 1200-Nm.If the modulus of rigidity of the shaft material G is 90 GPa, calculate: (i) The maximum shear stress (ii) The angle of twist in degrees Summary ... Read More
Reads ( 766 )| Price:
Original Price: |
Add to Cart |
Calculate Maximum Power Transmitted And Angle Of Twist In Degrees For Solid Steel Shaft
Question A solid steel shaft 3m long with a diameter of 5mm is to transmit power at a rotational speed of 800rpm.The modulus of rigidity of the shaft material G is 90 GPa. If the maximum stress is limited to 60MN/m2 determine the following. (i) The maximum power that could be transmitted (ii) The ... Read More
Reads ( 2055 )| Price:
Original Price: |
Add to Cart |
Calculate Change In Acceleration Of Particle Moving In Straight Line
Question A particle is initially at rest at point A on a straight line ABCD. The particle moves from point A to B with uniform acceleration, reaching B with the speed of 12m/s after 2 seconds. The acceleration then alters to a constant 1m/s2 and 8 uniformly to come to rest at D after further 10 sec ... Read More
Reads ( 869 )| Price:
Original Price: |
Add to Cart |
Calculate Velocity Of Cards And Loss Of Kinetic Energy After Cars Impact
Question A car of mass 1200kg traveling with a velocity of 30 meters per second collides head on into a stationary car which has a mass of 800kg.After the impact the two vehicles lock together and move in the same direction as the 1200kg car. (i) What is the velocity of the cars after the impact? ... Read More
Reads ( 989 )| Price:
Original Price: |
Add to Cart |
Calculate Velocity Of Train At Instant It Strikes Buffers And Strain Energy Gained By Buffers
Question A train of mass 15000kg is brought to rest when striking the buffers of a terminus. The buffers consist of two springs in parallel as shown in Figure5(b).The spring constant of each spring is 120kN/m. The springs are compressed by 0.75m when the train is brought to rest. Assuming that ther ... Read More
Reads ( 1811 )| Price:
Original Price: |
Add to Cart |
Calculate Maximum Acceleration, Maximum Velocity And Maximum Kinetic Energy For Piston
Question A piston of mass 0.2kg moves with simple harmonic motion. If the amplitude of the piston oscillation is 70mm and its period of oscillation is 0.1 second, calculate: (i) The maximum acceleration (ii) The maximum velocity (iii) The maximum kinetic energy. Summary The question be ... Read More
Reads ( 1390 )| Price:
Original Price: |
Add to Cart |
Calculate Velocity Of Mass When It Passes Through Mid Position Of Its Oscillation
Question A body of mass 2kg hangs from a spiral spring. When the mass is pulled down 10cm from its rest position and released. It vibrates with simple harmonic motion. The frequency of oscillation is 2.5 Hz. Calculate: (i) The velocity of the mass when it passes through the mid-position of its osc ... Read More
Reads ( 2362 )| Price:
Original Price: |
Add to Cart |
WHAT OUR STUDENTS SAY
When I got the opportunity to get my Masters in Finance Management from one of the top B-schools of London I jumped and took it. But once there I realized that I was being unable to keep up with the course structure and the way the professors wanted the assignments to be researched. That is when I found TheReliableTutor.com. Their online finance tutor guided me through the process and showed me how to structure the research and citations. Now my grades have improved and I can submit all my assignments and do my finance homework on time."
Nitin Kumar Student
I was totally unaware of what exactly needed to be written in the marketing plan assignment, based on the . I needed to first get an approval from my professor about the hypothetical business and a region where it needs to be promoted. When I approached TheReliableTutor I got relieved as they provided me with certain alternatives, as they are well aware of the regions of Singapore and assured me that their marketing assignment experts can care of anything my professor approves. It is needless to say that I got an A+ in the marketing plan assignment and many other assignments going forward.
Jun Hao Student
There was a research based assignment on the clinical services available for the aboriginals of New Zealand and for that I needed some expert who knows the nursing industry of New Zealand more than anything else. Luckily here I got hold of one lovely professor who helped me that assignment and many other assignments in the due time.
Sharon Nash Student
I was a bad place with my electricity assignment and was not sure how to apply the laws to get the numerical assignments done. Then I came in contact of one of my seniors in my college who told me about HwA. The service I got here was awesome and more than giving me a A in my assignment they also treated me with respect and helped me learn a lot.
Nicola Watson Student
Before approaching TheReliableTutor.com, zoology was one of the most difficult things in my life. But after taking sessions from TheReliableTutor.com, zoology has become more fun and more interesting to learn. Thank you guys..!!!
Christie Student
